Sendy on Amazon SES: Clean Your List Before Every Big Send
Sendy sends through your own Amazon SES account, so every bounce and complaint counts directly against you. Before a big send, confirm Sendy's bounce and complaint handling is working, verify the list, and send large lists in batches while watching the SES reputation dashboard. That combination keeps you out of an SES review.
Why Sendy users get hit harder
With a hosted email platform, the platform screens imports, applies its own suppression lists and absorbs some problems. With Sendy, you install the software and connect your own SES account. That is why it is inexpensive to run, and also why there is no buffer:
- SES tracks your bounce and complaint rates per account.
- If they climb too high, AWS can place the account under review or pause sending.
- Your sending domain's reputation with Gmail, Outlook and Yahoo is affected at the same time.
Amazon SES account under review for bounces covers the recovery process if you are already there. This post is about staying out.
Step 1: Make sure bounce handling works
Sendy learns about bounces and complaints through Amazon SNS notifications from SES. If those are not set up or have broken, bounced addresses stay active in Sendy and get mailed again next time, raising the bounce rate every campaign.
Check:
- In Sendy, the brand or list settings show bounce and complaint handling as set up.
- In the AWS console, your SES identity has notifications configured for bounces and complaints.
- After a test send to a known bad address, the subscriber is marked as bounced in Sendy.
Sendy's documentation describes the setup, and newer versions configure much of it automatically. If you migrated servers, changed domains or rotated AWS keys, test it again.
Step 2: Verify before importing
Bounce handling only removes addresses after they bounce. Each of those bounces has already counted. For any new or old list, verify first.
- Export the list you plan to import or send to.
- Remove duplicates with the duplicate email remover.
- Upload to the verify page.
- Import only the results you intend to send.
| Result | Import into Sendy? |
|---|---|
| Valid | Yes |
| Catch-all | Yes, as a separate list for later batches |
| Disposable | Usually no |
| Risky or unknown | Hold and re-check |
| Invalid | No |
Step 3: Import into separate lists
Sendy is organised around lists. Use that:
- Main list: valid, recently engaged subscribers.
- Older valid list: valid but not engaged recently.
- Catch-all list: sent last.
This lets you send in stages and stop if something goes wrong.
Step 4: Authenticate the sending domain
In SES, verify your domain with Easy DKIM, set a custom MAIL FROM domain so SPF aligns, and publish a DMARC record. Gmail and Yahoo require authentication for bulk senders, and Microsoft applies similar rules for high-volume senders to Outlook.com. Check your records with the bulk email authentication checker, and see what is a return-path address for why custom MAIL FROM matters.
Step 5: Send in batches
Sendy lets you schedule campaigns per list. For large sends:
- Send to the main list first.
- Check bounces and complaints in Sendy and the SES reputation dashboard.
- Send to the older valid list once numbers look healthy.
- Send to catch-all addresses last.
If your SES sending rate is high, consider lowering it in Sendy for big campaigns to the same provider, so you do not hit throttling. What is email throttling explains why.
Step 6: Watch the SES dashboard
AWS shows bounce and complaint rates for your account in the SES console. Check it after each batch, not only after the whole campaign. Exact thresholds that trigger a review are described in AWS documentation; bounce rate limits by platform summarises the published numbers.
Step 7: Keep the list clean over time
- Verify signups at the form so typos and bots never enter the list.
- Re-verify any list that has not been mailed for a few months.
- Remove subscribers who have not opened or clicked in a long time, after a re-engagement attempt; see sunset policies.
A pre-send checklist for Sendy
- SNS bounce and complaint notifications tested
- Domain authenticated in SES (DKIM, custom MAIL FROM, DMARC)
- List verified and deduplicated
- Catch-all contacts in a separate list
- Campaign split into batches
- SES reputation dashboard checked between batches
Common Sendy mistakes
- Assuming bounce handling works because it worked once. Server moves, new brands and key rotations can silently break notifications. Test after any change.
- Importing a whole old list into one Sendy list. Splitting by engagement and verification status gives you control over the send order.
- Sending at the maximum SES rate. A fast send is not always a good send. Lower the rate for big campaigns to the same providers.
- Reusing one SES account for very different mail. Transactional and marketing mail behave differently. Many senders keep them on separate identities or subdomains.
- Ignoring complaints. Bounces get attention, but complaint rates matter just as much to SES and to mailbox providers.
Quick answers
- Can Sendy verify emails itself? It handles bounces after sending; verification before import is a separate step.
- Should I use a dedicated IP with SES? Only at high, steady volume; low volume on a dedicated IP can hurt rather than help.
Verify before the next campaign
Upload your Sendy export on the verify page. You get 100 free email checks when you sign in with Google, no card. For large lists, see the monthly plans on the pricing page.
Common questions
Why does list quality matter so much with Sendy?
Sendy is software that sends through your own Amazon SES account. There is no platform in between absorbing problems. If a campaign bounces heavily, SES sees it against your account and can put it under review or pause sending.
Does Sendy remove bounced emails automatically?
Yes, when bounce and complaint notifications are set up. Sendy uses Amazon SNS to receive bounces and complaints from SES and marks those subscribers. If the notifications are not working, bounced addresses stay active and keep bouncing.
Should I verify a list before importing into Sendy?
Yes. Sendy's bounce handling only learns about bad addresses after they bounce, and each bounce counts against your SES account. Verifying first removes most of them before they are ever sent.
What happens if my SES account goes under review?
Amazon asks you to fix the cause and explain the steps you took. Sending may be limited or paused while it reviews. Cleaning the list and showing better practices is usually part of resolving it.
Check your list before you send
Real mailbox checks over SMTP, and nothing is sent to the address. Sign in with Google and your first 100 email checks are free, no card. Plans for bigger lists are on the pricing page.